Malaysia Watch Forum
Main Forums => Watch Reviews => Topic started by: Cocas on August 25, 2018, 06:26:58 PM
-
Ming 17.03 LE Blue
Case material: Grade 2 Titanium is light weight but non-glossy. Because of it's not heavy like stainless steel, the whole watch will not stick to your wrist and your sweat can dry up faster and you will not feel sticky.
Thickness & water resistance: it's amazingly for a GMT watch thickness is less than 10mm. Some more it got 100m water resistant. There are many watch brands could not achieve this.
Lume: the hands lume are Superluminova X1 grade, the dounut ring hours marker & ring are Superluminova C3 grade. The X1 could apply to hours marker because X1 cannot apply onto sapphire surface. X1 looks dimmed as compared against C3 during initial lume but the lume brightness will stabilize and look the same after about 2 minutes.
Crown: the crown is not a screw down crow. Its edge is sharp. Not sure is it because of grade 2 Ti is used. It's easy for turning the crown but certainly not comfortable for lady tender skin .
Dial: it got 3-parts sapphire dial. The centered dial part sunk lower than the outer dial. The hour hand is sitting within the centered dial surface. The special design allows the reduction in thickness.
The sapphire material is used and the blue color is amazing. So far the watery reflection with the hands "floating" on the blue dial effect. Other than Ming watch, I only can find it in Rolex Cellini 4016 watch. So far to my knowledge, there is no other watch brand makes watery dial like that.
To be continued....
-
Ming 17.03 LE Blue
Case material: Grade 2 Titanium is light weight but non-glossy. Because of it's not heavy like stainless steel, the whole watch will not stick to your wrist and your sweat can dry up faster and you will not feel sticky.
Thickness & water resistance: it's amazingly for a GMT watch thickness is less than 10mm. Some more it got 100m water resistant. There are many watch brands could not achieve this.
Lume: the hands lume are Superluminova X1 grade, the dounut ring hours marker & ring are Superluminova C3 grade. The X1 could apply to hours marker because X1 cannot apply onto sapphire surface. X1 looks dimmed as compared against C3 during initial lume but the lume brightness will stabilize and look the same after about 2 minutes.
Crown: the crown is not a screw down crow. Its edge is sharp. Not sure is it because of grade 2 Ti is used. It's easy for turning the crown but certainly not comfortable for lady tender skin .
Dial: it got 3-parts sapphire dial. The centered dial part sunk lower than the outer dial. The hour hand is sitting within the centered dial surface. The special design allows the reduction in thickness.
The sapphire material is used and the blue color is amazing. So far the watery reflection with the hands "floating" on the blue dial effect. Other than Ming watch, I only can find it in Rolex Cellini 4016 watch. So far to my knowledge, there is no other watch brand makes watery dial like that.
To be continued....
More photo pls
Sent from my iPhone using Tapatalk
-
Ming 17.03 LE Blue
Case material: Grade 2 Titanium is light weight but non-glossy. Because of it's not heavy like stainless steel, the whole watch will not stick to your wrist and your sweat can dry up faster and you will not feel sticky.
Thickness & water resistance: it's amazingly for a GMT watch thickness is less than 10mm. Some more it got 100m water resistant. There are many watch brands could not achieve this.
Lume: the hands lume are Superluminova X1 grade, the dounut ring hours marker & ring are Superluminova C3 grade. The X1 could apply to hours marker because X1 cannot apply onto sapphire surface. X1 looks dimmed as compared against C3 during initial lume but the lume brightness will stabilize and look the same after about 2 minutes.
Crown: the crown is not a screw down crow. Its edge is sharp. Not sure is it because of grade 2 Ti is used. It's easy for turning the crown but certainly not comfortable for lady tender skin .
Dial: it got 3-parts sapphire dial. The centered dial part sunk lower than the outer dial. The hour hand is sitting within the centered dial surface. The special design allows the reduction in thickness.
The sapphire material is used and the blue color is amazing. So far the watery reflection with the hands "floating" on the blue dial effect. Other than Ming watch, I only can find it in Rolex Cellini 4016 watch. So far to my knowledge, there is no other watch brand makes watery dial like that.
To be continued....
Very good review and can’t wait for part 2... thanks bro
Sent from my iPhone using Tapatalk
-
Putting up more photos now.
-
Great review
Thnx
Last time I didn’t pull the trigger mainly due to the lug is sharp
Won’t cut your wrist
But I hold, carry n play with daughter often... so worry on that
Sent from my iPhone using Tapatalk
-
Great review
Thnx
Last time I didn’t pull the trigger mainly due to the lug is sharp
Won’t cut your wrist
But I hold, carry n play with daughter often... so worry on that
Sent from my iPhone using Tapatalk
Yes, its lugs tip are pointy like Rolex.
But compared against the sharp crown edge, then the pointy lugs are nothing.
-
Great review
Thnx
Last time I didn’t pull the trigger mainly due to the lug is sharp
Won’t cut your wrist
But I hold, carry n play with daughter often... so worry on that
Sent from my iPhone using Tapatalk
Yes, its lugs tip are pointy like Rolex.
But compared against the sharp crown edge, then the pointy lugs are nothing.
Crown edge also sharp ?
Sent from my iPhone using Tapatalk
-
Great review
Thnx
Last time I didn’t pull the trigger mainly due to the lug is sharp
Won’t cut your wrist
But I hold, carry n play with daughter often... so worry on that
Sent from my iPhone using Tapatalk
Yes, its lugs tip are pointy like Rolex.
But compared against the sharp crown edge, then the pointy lugs are nothing.
Crown edge also sharp ?
Sent from my iPhone using Tapatalk
To be exact, the sharp areas are the ridges on the crown edge.
Here are some photos.
-
Industrial finish without hand further finish ?
Sent from my iPhone using Tapatalk
-
Industrial finish without hand further finish ?
Sent from my iPhone using Tapatalk
Yes, very likely.
-
how much r they?
-
how much r they?
I remember it's in CHF and couldn't recall the exact amount. Certainly after conversion, it's below RM 6k.
-
If by any chance you feel like selling it, please let me know bro! Hehe. Would be keen to get it.
Sent from my iPhone using Tapatalk